Aluminum Window Processing Equipment –corner Crimping Machine
Corner crimping machine is a special equipment for the production of high grade aluminum alloy doors and Windows on broken bridge. Some areas are also called corner extruders, corner crashers, corner machines. According to the different Angle can be set, divided into single-head Angle machine, double-head Angle machine, four-head Angle machine.
This machine is composed of body, working table, positioning oil cylinder, auxiliary positioning device, punching and riveting device, Angle setting oil cylinder, Angle setting slide plate, electric control panel, foot switch and other main parts. Pneumatic system by electromagnetic valve, pressure gauge, Oil mist, water separator and other components. Hydraulic system consists of hydraulic pump, solenoid valve, high pressure hose, hydraulic relay and so on.
The Angle setting slide plate is pushed forward by the Angle setting oil cylinder, and the Angle setting slide plate moves forward while pushing the left and right punching and riveting shaft. The Angle setting knife on the punching and riveting shaft connects the aluminum doors and Windows at a 90-degree Angle.
This machine is a new model developed on the basis of absorbing the advantages of similar foreign products. This machine adopts gas, electricity, hydraulic connection and operation control. Because of the new structure of mechanical linkage, it eliminates the influence of oil pressure fluctuation on the quality of Angle formation, so that Angle formation is completely synchronized, Angle formation depth is more consistent, and Angle formation 90 degree Angle is more accurate. In addition, the positioning device with adjustable front and rear position and adjustable front and rear distance is suitable for processing profiles with different section shapes and sizes.
The installation
Environment and requirements Corner - forming machine should be installed on dry, dust-free, non - corrosive gas indoor hard cement floor.
Unpacking is in place Remove the fastening screw from the base of the corner-setting machine, and then move the corner-setting machine to the installation position with a handling tool.
the grounding Angle machine body must be grounded, grounding using yellow and green double stranded and copper wire, its section area is not less than 2.5 square mm, grounding between the body and the main grounding point resistance should be less than 4 ohms.
connect the power The input voltage is 380V and the frequency is 50HZ.
by air Install the air source on the triplet joint of air source treatment on the side of the fuselage, and adjust the air pressure to 0.5-0.8mpa after checking no air leakage.
Check the oil route Open the rear cover of the body, and keep the tank level above the center line of the oil mark to prevent the pump from being empty. A 120-mesh filter is used to remove impurities in the new oil during refueling.
Operating rules for corner machine
Personnel have been trained and qualified before operation, and all protective and safety devices of the equipment are intact and functioning;
Operators should wear appropriate work clothes, earmuffs and safety glasses when necessary;
Adjust the machine according to the size of profile according to the compressed air of 7-8bar;
Apply strong glue to the end face and profile inner cavity of the corner code. After pressurizing the corner code, wipe the spilled glue;
Put the profile of the Angle group on the work table, adjust the v-shaped backboard, and work after positioning;
step on the left foot switch "lift the slide seat", make the slide seat to raise the profile positioning;
step on the right foot switch "pressure" do not put, make the pressure punch through the pressure cylinder for pressure, so that the profiles are connected to each other, the group Angle is finished;
Release the pedal switch on the right side to "pressurize", the working process is finished, and the pressurized punch and pressurized cylinder are reset again;
Release the pedal switch on the left side to "lift the locking cylinder press block in the middle of the slide seat" and reset it with the slide seat;
Check the pressed profile;
Open fire should not be used for testing and maintenance.
The maintenance of the machine shall be carried out in accordance with the equipment operation, maintenance and maintenance system.
So that's all there is to know about corner crimping machines. To learn more, click on the link below for more details. http://www.glasswindowequipment.com.
Shandong Care Machinery Technology Co., Ltd
8th Building Xinmao Tech Park, No.1 Zidong Avenue,Jinan China
18563727557
18563727557
market@glasswindowequipment.com
www.glasswindowequipment.com/aluminum-window-processing-equipment-corner
